PRODUCT LIST
Open single crankshaft precision punch
Open Double crankshaft precision punch
Semi-closed single crankshaft precision punch
Close single-crankshaft precision punch
Closed double point crankshaft precision punch
Close double-crankshaft precision punch
Open single point servo model
Gantry dual point servo model
Special machine for open double crankshaft battery shell
Closed single point high speed punch
Three post guides high-speed precision punch
Gant Type Speed Precision Four Post Guider Press Machine
Straight Column Type Four-points ecdenttric press machine
Split and close double-crankshaft precision press machine
CONTACT US
Service Hotline400 100 5226
- Tel: 400 100 5226
- Fax: 0510-68392919
- E-mail: sherry@yisto-east.com
- Address: No.422, Xizhang Road, Gushan Town, Jiangyin, Wuxi, China
Your location: News >> Industry News
Punch use precautions before punching work
Release date: 2024-06-20 17:31:06 Visits: 808
(1) Check the lubrication of each part and make the lubrication of each lubrication charge-filled;
(2) Check if the mold installation is correct - rely on;
(3) Check if the compressed air pressure is within the specified range;
(4) Check whether each switch button is 0-sensitive, and the motor must be turned on after the flywheel and clutch are disengaged;
(5) Make the press perform several idle strokes to check the operation of the brake, clutch and operating part;
(6) Check the main motor for abnormal heat, abnormal vibration, abnormal sound, etc.;
(7) adding a lithium ester oil to the slider with a manual oil pump;
(8) Check and adjust the feeder roller gap to the process requirements;
(9) Check and keep the oil level of the oil mister to meet the specified requirements;
(10) When the motor starts, check if the direction of rotation of the flywheel is the same as the swing sign.
At work
(1) The lubricating oil should be used to pump the lubricating oil to the lubrication point at regular intervals;
(2) When the performance of the press is not familiar, the press may not be adjusted without authorization;
(3) It is forbidden to punch two sheets at the same time;
(4) If the work is found to be abnormal, stop working and check in time.
After work
(1) Disengage the flywheel and the clutch, cut off the power supply, and release the remaining air;
(2) Wipe the press clean and the countertop is coated with rust oil;
(3) Make a record after each operation or maintenance.
(2) Check if the mold installation is correct - rely on;
(3) Check if the compressed air pressure is within the specified range;
(4) Check whether each switch button is 0-sensitive, and the motor must be turned on after the flywheel and clutch are disengaged;
(5) Make the press perform several idle strokes to check the operation of the brake, clutch and operating part;
(6) Check the main motor for abnormal heat, abnormal vibration, abnormal sound, etc.;
(7) adding a lithium ester oil to the slider with a manual oil pump;
(8) Check and adjust the feeder roller gap to the process requirements;
(9) Check and keep the oil level of the oil mister to meet the specified requirements;
(10) When the motor starts, check if the direction of rotation of the flywheel is the same as the swing sign.
At work
(1) The lubricating oil should be used to pump the lubricating oil to the lubrication point at regular intervals;
(2) When the performance of the press is not familiar, the press may not be adjusted without authorization;
(3) It is forbidden to punch two sheets at the same time;
(4) If the work is found to be abnormal, stop working and check in time.
After work
(1) Disengage the flywheel and the clutch, cut off the power supply, and release the remaining air;
(2) Wipe the press clean and the countertop is coated with rust oil;
(3) Make a record after each operation or maintenance.